Sportbike Track Gear
Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

How To: Install HealTech GIpro X-Type (Gear Indicator) ***Sponsored by CalSportBike***

This is a discussion on How To: Install HealTech GIpro X-Type (Gear Indicator) ***Sponsored by CalSportBike*** within the R6 How-To Guides forums, part of the Yamaha R6 category; Todd exchanged it for you? Dude.. Todd is fucking awesome! Glad you like it man, that blue looks pretty pimp ...

  1. #11
    :D dzuyd's Avatar
    Join Date
    Jan 2008
    Posts
    8,403
    Post Thanks / Like

    Default Re: How To: Install HealTech GIpro X-Type (Gear Indicator) ***Sponsored by CalSportBike***

    Todd exchanged it for you? Dude.. Todd is fucking awesome! Glad you like it man, that blue looks pretty pimp . I only organized the drawing, you can thank Todd for the giveaway And also thank him by shopping with him also Cal-Sportbike Distribution ::: HealTech Electronics, Speedo Healer, Pipercross, Galfer, GIPro, X-TRE

  2. #12
    Always watching... CephasGT's Avatar
    Join Date
    Jan 2008
    Location
    Dayton, OH
    Posts
    7,214
    Post Thanks / Like
    Blog Entries
    4

    Default Re: How To: Install HealTech GIpro X-Type (Gear Indicator) ***Sponsored by CalSportBike***

    Todd is good peeps, for sure. I've been dealing with him and his company for almost five years now!

    "We sleep soundly in our beds because rough men stand ready in the night to visit violence on those who would do us harm." - Winston Churchill
    "Conscience is but the name which cowardice, fleeing the battle, scrawls upon its shield." - Oscar Wilde

  3. #13
    Member JPR6's Avatar
    Join Date
    Apr 2009
    Posts
    42
    Post Thanks / Like

    Default Re: How To: Install HealTech GIpro X-Type (Gear Indicator) ***Sponsored by CalSportBike***

    I really want a gear indicator but the last one ( Datatool digital gear indicator) i bought i sent back because no one could figure out how to install it to a 07 R6, can you guys point the wire colors out on this model bike. Cause if is this easy i''l buy one hell maybe 2

  4. #14
    :D dzuyd's Avatar
    Join Date
    Jan 2008
    Posts
    8,403
    Post Thanks / Like

    Default Re: How To: Install HealTech GIpro X-Type (Gear Indicator) ***Sponsored by CalSportBike***

    The wire colors will be the same for all model R6. The only difference should be that for 3rd gen bikes, all the wires needed will be located under the tank, so you don't have to look for the power cable in the side panel.

    See Step #7:

    7. Connect the GIpro Red wire to a switched +12v wire. The installation manual recommends the rear brake light switch, so I went with that. For my '05 R6, the wire needed was behind the side panel (brake side) of the bike. The Manual specifies a 2-pole connector under the tank, but I suspect this may be for newer bikes.

  5. #15
    Member JPR6's Avatar
    Join Date
    Apr 2009
    Posts
    42
    Post Thanks / Like

    Default Re: How To: Install HealTech GIpro X-Type (Gear Indicator) ***Sponsored by CalSportBike***

    Thank you for the info, gona get one before my next trackday

  6. #16
    n00b
    Join Date
    Oct 2011
    Posts
    6
    Post Thanks / Like

    Default

    I really struggled with this install. I installed the GIPROX and the SpeedoHealer for my '05 R6 Rossi at the same time. The looms for both items look the same except for the gear indicator has the power and rpm signal wires. When you swap both looms around (like I did) it will partially work but get no RPM signal. It took me a long time to work it out, otherwise it is a very simple install. I suggest labelling each loom at the plug end and plug it into the right item to start with!
    Greg

Page 2 of 2 FirstFirst 12

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •